• Telecom & ICT Equipment Supplier
  • Multi-Vendor Sourcing
  • Worldwide Shipping
YT CIG Telecom & ICT Equipment
Get a Quote

RRU selection guide: 4T4R vs 8T8R and band planning

Updated on 2026-11-19

Last updated: 2026-11-19

For most FDD coverage layers in the low and mid bands, a 4T4R RRU is the economical fit; an 8-branch radio earns its keep on TDD mid-band capacity sites, where beamforming lifts cell-edge throughput. Band choices should be read against the 3GPP TS 38.104 operating-band framework, and the catalog pages cited below show how the two classes are stocked across vendors.

What do 4T4R and 8T8R mean on an RRU datasheet?

The notation on a remote radio unit (RRU) datasheet counts transmit and receive branches. 4T4R means four transmit and four receive paths; 8T8R means eight of each. Transmit branches shape what the radio can send: how total output power is split across paths, how many downlink MIMO layers the baseband can map, and (in multi-branch TDD radios) whether per-user service beams can be formed. Receive branches shape uplink performance: more RX paths give the baseband more copies of the handset signal to combine, which is why receive diversity has been standard on macro cells since single-carrier days.

Vendor datasheets print the branch count together with the band and per-path power. The Huawei RRU3281 technical specifications describe a 4T4R LTE FDD unit delivering four 40 W output paths (some 160 W combined) with support for up to three LTE carriers (Huawei RRU3281 Technical Specifications). The ZTE ZXSDR R8978 S2300 user manual describes an eight-channel TD-LTE RRU for macro cells, operating in the 2300–2400 MHz range from a −48 V DC feed, with 100/110/220 V AC options also documented (ZTE ZXSDR R8978 user manual).

TDD radios are frequently described by path count. A catalog line reading “TDD RRU (20 W × 8)” (as the YT CIG listing for the ZTE R8978 S2300 does) is describing the same eight-branch hardware.

When you compare two RRUs, read four datasheet fields together: operating band (with its duplex mode), branch configuration, per-path output power, and the fronthaul interface (CPRI line rate and port count on Huawei and ZTE units). Two radios that share a band but differ in branch count are different product decisions, not drop-in swaps.

4T4R: the FDD coverage workhorse

Most FDD coverage layers are built on this configuration. The typical deployments are rural and suburban macro sites on low or mid FDD bands, umbrella cells that must carry legacy and LTE/NR traffic in the same band, and any site where tower loading, power budget or budget-per-site constraints push the buyer toward a proven, widely stocked radio class.

Concrete examples make the class easier to price. The Huawei RRU5901w listed in the YT CIG catalog covers the 1800 MHz FDD band with TX 1805–1880 MHz / RX 1710–1785 MHz and delivers 4 × 40 W output power as an outdoor 4T4R unit (order code 02312AAR, per the catalog listing). The Huawei RRU3281 provides the same four 40 W paths in a multi-carrier LTE FDD package (Huawei RRU3281 Technical Specifications). Where the link budget needs more radiated power than 4 × 40 W, the Huawei RRU5904 platform moves to 4 × 60 W (240 W combined) and is described in Huawei’s product documentation as an outdoor RRU working with a power cabinet (RRU5904 Description). Nokia’s AirScale RRH 4T4R specification document likewise lists a macro-class output of 4 × 40 W, so this power class is broadly consistent across the three vendors most stocked in the secondary market.

Three planning habits reduce rework when you select 4T4R:

  • Confirm the band variant code as well as the model: the same RRU family ships with band-specific suffixes, and the RF spec changes with it.
  • Match the antenna to four ports with proper cross-polarization, since four-branch uplink combining assumes a four-port receive path.
  • Check the fronthaul budget: multi-carrier 4T4R operation raises the CPRI line rate requirement on the BBU side.

8T8R: beamforming on TDD capacity layers

Eight-branch radios belong to capacity and uplink-sensitive scenarios. The classic use is a TDD mid-band macro cell, the 2300–2400 MHz TD-LTE layer is the textbook case, and the ZTE ZXSDR R8978 S2300 in the YT CIG catalog is exactly this class: an eight-channel TD-LTE RRU for macro cells, listed at 20 W × 8, supporting TD-LTE 4 × 20 MHz carrier aggregation with dual TRX channels (catalog listing; ZTE ZXSDR R8978 user manual). In NR terms this maps to the same planning logic as band n41-class TDD deployments (3GPP TS 38.104).

Why eight branches matter in these scenarios: a TDD radio hears the uplink on the same frequencies it transmits on, so uplink channel measurements can drive downlink beam weights. With eight TX branches the radio can form narrower service beams toward individual users, which concentrates radiated power where the user is and suppresses interference off the beam direction. Huawei’s 8T8R antenna beamforming technology documentation is built around exactly this weight-configuration and SINR-improvement mechanism (Huawei 8T8R Antenna Beamforming Technology).

The uplink payoff has a published magnitude. Huawei’s Sub-3GHz FDD Gigaband white paper states that dual-band 8T8R multi-antenna configurations raise uplink coverage by 3–6 dB compared with conventional configurations, a number that translates directly into fewer cell-edge uplink drops at the same site count (Huawei Sub-3GHz FDD Gigaband white paper). Huawei has since published a dedicated FDD 8T8R Antenna Performance White Paper (2024) that proposes antenna-side performance specifications for 8-branch FDD deployments, confirming that FDD deployments use beamforming as well (Huawei FDD 8T8R Antenna Performance White Paper, 2024).

Choose 8T8R when the scenario is dense-urban capacity, an uplink-limited layer (deep-indoor users at the cell edge), or a TDD band where beamforming is the main lever for per-user throughput. Its cost drivers are concrete: more antenna ports, higher fronthaul load, and a heavier bill of materials than the equivalent 4T4R unit.

How do 4T4R and 8T8R compare side by side?

The two configurations differ on parameters a buyer can verify from vendor documentation:

Parameter 4T4R (typical FDD coverage RRU) 8T8R / eight-path (typical TDD capacity RRU)
Branches 4 TX + 4 RX 8 TX + 8 RX
Catalog examples Huawei RRU3281 (4 × 40 W); RRU5901w (band 3, 4 × 40 W); RRU5904 (4 × 60 W) ZTE ZXSDR R8978 S2300 (20 W × 8, TD-LTE 2300–2400 MHz)
Band types most common FDD low/mid bands (n1, n3 in NR terms) TDD mid bands (n41-class, B40); FDD 8T8R exists via antenna-side beamforming
Downlink behavior Four transmit branches, multi-carrier capable Narrow per-user service beams via beamforming
Uplink behavior Four-branch receive combining Beamforming and combining; Huawei cites 3–6 dB uplink coverage gain for dual-band 8T8R vs conventional configurations
Power feed −48 V DC typical −48 V DC, AC options documented for the ZTE R8978
Antenna ports 4 8
Typical role Coverage layer Capacity layer / uplink-sensitive sites

Read as a rule of thumb: 4T4R buys wide-area coverage at the lowest cost per site, while 8T8R buys per-user throughput and uplink reach where spectrum and traffic density justify the extra branches. Each maps to a different layer of the same network.

How does 3GPP TS 38.104 frame the band choices?

3GPP TS 38.104 is the NR base station radio specification, and its operating-band tables are the vocabulary buyers and vendors share when ordering radios. Everything in scope for sub-7 GHz RRUs sits in FR1, which the spec defines as 410 MHz to 7.125 GHz (3GPP TS 38.104, Table 5.2-1). Each operating band row carries a band number, UL/DL frequency ranges and a duplex mode, FDD bands have separate uplink and downlink ranges with a defined TX–RX frequency separation, while TDD bands use one range for both directions.

The TDD bands most relevant to 8-branch capacity radios are n41 at 2496–2690 MHz, n78 at 3300–3800 MHz and n79 at 4400–5000 MHz (3GPP TS 38.104, Table 5.2-1). The FDD bands most relevant to 4T4R coverage layers include n1, with UL 1920–1980 MHz and DL 2110–2170 MHz and a 190 MHz TX–RX separation, and n3, with UL 1710–1785 MHz and DL 1805–1880 MHz and a 95 MHz separation (3GPP TS 38.104, Table 5.4.4-1).

These numbers are not academic: they let you verify a datasheet listing line by line. Take the catalog’s Huawei RRU5901w entry, TX 1805–1880 MHz / RX 1710–1785 MHz. Set the TX range against the n3 downlink range and the RX range against the n3 uplink range and they match exactly, which confirms the unit is a band 3 (1800 MHz) FDD radio and not one of the neighboring variants. That two-minute check catches ordering mistakes that otherwise surface at installation.

For procurement, three rules follow from the spec:

  • Order by band variant as well as by family name; the RF specification, duplexer and allowed channel bandwidths all live in the band-specific variant.
  • Confirm the duplex mode matches your spectrum licence; a TDD radio cannot serve an FDD licence or vice versa.
  • When a datasheet cites “bands” without numbers, map them to the TS 38.104 table yourself before comparing prices across vendors.

How should you plan bands across low, mid and high spectrum?

Band planning inside FR1 is a layering exercise: each frequency layer plays a different role, and the RRU configuration should follow the role. The verified ranges below come straight from the TS 38.104 tables cited above.

Band (TS 38.104) Duplex Frequency range Typical planning role
n3 FDD UL 1710–1785 / DL 1805–1880 MHz 1800 MHz coverage workhorse; 4T4R class
n1 FDD UL 1920–1980 / DL 2110–2170 MHz 2100 MHz FDD layer; coverage plus capacity
n41 TDD 2496–2690 MHz 2.6 GHz capacity macro; 8-branch beamforming class
n78 TDD 3300–3800 MHz 3.5 GHz capacity/hotspot layer; beamforming expected
n79 TDD 4400–5000 MHz high-band capacity in dense areas

Layer the plan top-down by propagation, then bottom-up by capacity. Lower frequencies reach farther per watt, so the low/mid FDD layers (n3, n1) define the coverage footprint, this is where 4T4R is the standard choice, as covered above. Mid TDD layers (n41, then n78 and n79) carry the traffic in dense cells; here the extra branches of an 8-branch radio convert directly into beamforming gain, and the 3–6 dB uplink coverage figure cited from Huawei’s white paper is what buys back the link budget the higher frequency costs you.

Duplex mode is the branch-count gate. On TDD layers, channel reciprocity lets the radio derive downlink beam weights from uplink measurements, which is why eight-path TDD units such as the ZTE R8978 S2300 are the norm for capacity macros. On FDD layers, beamforming must come from the antenna side; Huawei’s FDD 8T8R Antenna Performance White Paper (2024) addresses exactly that antenna-side specification, and treating it as an antenna-system decision keeps the bill of materials coherent.

Two cross-checks keep the plan honest. First, confirm every planned band’s TX–RX separation against Table 5.4.4-1, the n3 separation of 95 MHz differs from n1’s 190 MHz, and duplexers are band-specific. Second, if a site must serve several layers, plan one RRU per band (or a vendor’s documented multi-band unit); one radio covering n3 plus n41 has no documented configuration, which is why the catalog keeps band-specific variants separate.

What power and installation constraints should you check before ordering?

The electrical and mechanical items below are where RRU orders go wrong in practice, so check them before quotation; after delivery they become claims.

  • Power feed. −48 V DC is the standard feed for outdoor macro RRUs; the ZTE R8978 S2300 user manual documents a −48 V DC feed with 100/110/220 V AC options (ZTE ZXSDR R8978 user manual). Higher-power 4T4R units such as the RRU5904 at 4 × 60 W (240 W combined) are documented as working with a power cabinet (RRU5904 Description), so plan the cabinet alongside the radio.
  • Weight and dimensions. Several catalog listings carry no dimensions (the pages state “dimensions not specified in available data”) so request the engineering datasheet for the specific variant before structural or crane planning. Never extrapolate from a sibling model.
  • Antenna ports. Four ports on a 4T4R radio, eight on an 8-branch unit; the antenna and its jumpers must match, which is why the catalog’s 698–2700 MHz macro antenna is listed as a companion product for the coverage-layer radios.
  • Fronthaul. CPRI fiber runs to the BBU; multi-carrier and eight-branch modes raise the line-rate requirement. The catalog lists the BBU chassis as the baseband side of the pairing.
  • Condition. Every RRU catalog page states that condition (new, refurbished or used) is confirmed on quotation, so fix that expectation in the RFQ.

These items fail when they are checked late. One pass through the variant-specific datasheet before the RFQ goes out covers all five.

Which YT CIG catalog RRU parts map to each scenario?

YT CIG operates a multi-vendor equipment catalog (Huawei, ZTE, Nokia and Ericsson among the stocked brands), and the RRU shelf currently spans both configurations discussed in this guide. The mapping below links each scenario to live catalog pages, all verified online at the time of writing.

  • FDD coverage layer, 1800 MHz (band n3): the Huawei RRU5901w, 4T4R, 4 × 40 W, TX 1805–1880 / RX 1710–1785 MHz.
  • FDD multi-carrier coverage: the Huawei RRU3281, 4T4R, four 40 W paths, up to three LTE carriers.
  • High-power 4T4R where the link budget needs it: the Huawei RRU5904, 4 × 60 W (240 W combined), power-cabinet pairing documented.
  • Multi-mode 4T4R for distributed base stations: the Huawei RRU5916, listed as a 4T4R multi-mode outdoor RRU.
  • Eight-path TDD capacity macro: the ZTE ZXSDR R8978 S2300, 20 W × 8, TD-LTE 2300–2400 MHz, 4 × 20 MHz carriers.
  • Ericsson catalog entry: the Ericsson RRU6630, listed as a remote radio unit for telecom network infrastructure; request the variant-specific datasheet for band and power details, as the public listing carries no RF figures.

The RRU category guide aggregates the radio family, and the catalog’s 698–2700 MHz macro antenna covers the antenna side for coverage-layer deployments. When you send an RFQ, state the band (ideally as the TS 38.104 band number), the duplex mode, the branch configuration you plan for, and the site power constraints, that is the minimum set that lets a supplier quote the right variant in the right condition, whether new, refurbished or used as applicable.

FAQ

Can a 4T4R site be upgraded to 8T8R later, or does it need new hardware?

Branch count is fixed in the radio hardware. The Huawei RRU3281 is built as 4T4R with four 40 W paths, and the ZTE R8978 S2300 is built as an eight-channel unit, neither configuration is a firmware option on the other. Upgrading means replacing the RRU and re-checking the antenna port count and fronthaul loading against the new branch configuration.

Our spectrum is FDD. Does an 8-branch radio still make sense?

It can, with the gain moved to the antenna side. On FDD the radio cannot derive downlink weights from uplink sounding, so Huawei’s FDD 8T8R Antenna Performance White Paper (2024) proposes antenna-side performance specifications for exactly this case. Budget the antenna change as part of the project: an eight-branch radio on a four-port antenna array will not deliver the beamforming gain that justified it.

A listing says 2.6 GHz. Is that band n41?

Only if both ranges sit inside 2496–2690 MHz. Band n41 is TDD, so it uses one range for uplink and downlink; a 2.6 GHz listing that quotes separate uplink and downlink ranges with a TX–RX separation is describing an FDD band, and the TS 38.104 Table 5.2-1 row will name it. Ask for the band number before comparing prices across vendors.

How do I turn the 3–6 dB uplink figure into a site count?

Treat it as link-budget margin at the cell edge, where uplink is weakest. The 3–6 dB figure comes from Huawei’s Sub-3GHz FDD Gigaband white paper for dual-band 8T8R configurations. A site short of its uplink edge rate by less than that margin can recover it without a new site; a larger shortfall belongs to antenna height, tilt or site density.

Can I mix Huawei and ZTE RRUs under one base station?

In practice, no. An RRU is engineered to operate with its own family’s BBU over the CPRI fronthaul, the ZTE ZXSDR R8978 user manual, for example, describes the unit as operating with a ZTE BBU. Vendor documentation does not support cross-vendor BBU–RRU pairing, so plan each vendor’s radios under its own baseband and keep the fronthaul topology per vendor.

Are the RRUs in the catalog available new, refurbished or used?

All three grades are handled, with condition confirmed on quotation: every RRU equipment page in the catalog states that condition is confirmed on quotation, new, refurbished or used as applicable. State your grade requirement and acceptance criteria (for example test-report expectations) in the RFQ so the quotation returns matching stock.

Need a specific part?

Send the part number and quantity — we confirm condition, availability and price before you commit.