• Telecom & ICT Equipment Supplier
  • Multi-Vendor Sourcing
  • Worldwide Shipping
YT CIG Telecom & ICT Equipment
Get a Quote

How to choose a 100G QSFP28 transceiver

Updated on 2026-11-19

CWDM4 and LR4 both carry 100G over duplex single-mode fiber on four wavelengths; LR4 (IEEE 802.3bm) is rated to 10 km, CWDM4 (MSA) to 2 km. For a 40 km 100G link, choose QSFP28 ER4 (the IEEE-defined 40 km interface) or ZR4 for extra margin. YT CIG supplies both in new and refurbished condition.

The QSFP28 generation: what the form factor covers

A 100G QSFP28 transceiver is a hot-pluggable optical module that converts 100 Gb/s Ethernet traffic into four parallel optical lanes and back. The QSFP28 mechanical form factor is defined by SFF-8661, and its management interface, which exposes digital diagnostics such as module temperature and per-lane optical power, follows SFF-8636; the CWDM4 MSA Technical Specifications Rev 1.0 states both dependencies explicitly for QSFP28 CWDM4 modules (§1.5, §1.8). Each lane runs at 25.78125 GBd, so a QSFP28 module puts 103.125 Gb/s on the fiber, of which 100 Gb/s is Ethernet payload (CWDM4 MSA Rev 1.0, Table 2-3).

Two architectures divide the portfolio. Parallel multimode modules (100GBASE-SR4 and its extended-reach ESR4 class) split the four lanes across an MPO connector and OM3/OM4 fiber, which keeps the optics inexpensive but confines reach to hundreds of meters. Serial WDM modules (CWDM4, LR4, ER4, and ZR4) combine the four lanes onto a single duplex single-mode pair at distinct wavelengths, extending reach from 2 m to tens of kilometers over G.652 fiber. Choosing among the WDM variants comes down to three variables: the reach you need, the measured loss of the plant between the two ends, and the wavelength plan your counterpart equipment uses.

The 100G QSFP28 product family on ytcig.com covers all of these variants across multiple original vendors, and the overview 100G QSFP28 Optical Transceivers guide covers the SR4/CWDM4/LR4/DWDM variants.

What separates QSFP28 CWDM4 from LR4?

The difference comes down to wavelength plan, reach, and optical budget. Both are duplex single-mode, four-lane, LC-connected 100G modules, but their lanes sit on different wavelength grids, their specified reach differs by a factor of five, and their transmitters run at different power classes.

CWDM4 assigns its lanes to the 20 nm coarse-WDM grid at 1271, 1291, 1311, and 1331 nm (the same grid ITU-T G.694.2 defines across 1271 to 1611 nm) with each lane held to a ±6.5 nm window (CWDM4 MSA Rev 1.0, Table 2-1). LR4 instead places its lanes on the tighter LAN-WDM plan at 1295.56, 1300.05, 1304.58, and 1309.14 nm around a 1310 nm specification wavelength (IEEE 802.3bm). The two plans share no lane wavelength, a practical consequence buyers often miss: CWDM4 and LR4 do not align lane-for-lane, so each link should run the same variant class at both ends.

Reach follows from the budgets behind those wavelengths. CWDM4 is specified for a 2 m to 2 km operating range with an illustrative power budget of 8.0 dB, including up to 5.0 dB of channel insertion loss (CWDM4 MSA Rev 1.0, Tables 2-2 and 2-5). LR4 carries a 6.3 dB maximum channel insertion loss and a 2 m to 10 km operating range over OS2/G.652 single-mode fiber (IEEE 802.3bm). Transmitter classes differ accordingly: CWDM4 launches at most +2.5 dBm per lane, with a −6.5 dBm informative minimum, while LR4-class modules specify −4.3 to +4.5 dBm per lane (CWDM4 MSA Table 2-3; vendor QSFP28 LR4 datasheets). Error-correction posture differs too: the CWDM4 MSA requires the host to enable RS(528,514) FEC and defines the optical link at a 5 × 10⁻⁵ pre-FEC BER (§1.7), whereas LR4 is specified without FEC at a 10⁻¹² BER target at the MAC/PLS service interface (IEEE 802.3bm).

Attribute QSFP28 CWDM4 QSFP28 LR4 QSFP28 ESR4 QSFP28 ZR4
Governing specification CWDM4 MSA Technical Specifications Rev 1.0 IEEE 802.3bm (100GBASE-LR4) Vendor-supported extended-reach SR4 class Vendor-defined extension of the LR4/ER4 wavelength plan
Fiber and connector Duplex SMF (G.652), LC duplex Duplex SMF (G.652), LC duplex Multimode OM3/OM4, MPO-12 Duplex SMF (G.652), LC duplex
Lane wavelengths 1271 / 1291 / 1311 / 1331 nm (20 nm CWDM grid per ITU-T G.694.2) 1295.56 / 1300.05 / 1304.58 / 1309.14 nm (LAN-WDM) 850 nm, 4 parallel lanes LAN-WDM lanes in the 1310 nm window
Nominal reach 2 m to 2 km 2 m to 10 km (OS2) Up to 300 m over OM4 (~170 m over OM3) Up to 80 km (vendor-typical)
Link-budget reference 8.0 dB budget incl. 5.0 dB channel insertion loss (MSA Table 2-5) 6.3 dB max channel insertion loss (IEEE 802.3bm) Vendor-defined; SR4 baseline is 1.9 dB over 100 m OM4 Vendor-engineered budget; confirm per datasheet
Typical application DCI and campus SMF runs up to 2 km Metro spans up to 10 km Intra-building and intra-campus MMF, 100–300 m Regional and long spans, 40–80 km

For a 40 km span over single-mode fiber, specify a 100GBASE-ER4 QSFP28. IEEE 802.3bm defines ER4 for a 2 m to 40 km operating range on OS2 fiber with an 18.0 dB maximum channel insertion loss, running the same four LAN-WDM lanes LR4 uses (1295.56–1309.14 nm). At the standard’s 0.4 dB/km OS2 figure, 40 km of fiber accounts for 16 dB; the IEEE tables assume a 2.0 dB connection-and-splice allocation, which puts that channel at 18.0 dB, exactly at the ER4 budget limit with no margin. The same arithmetic sits far outside LR4’s 6.3 dB allocation, which covers 10 km on the same basis, and outside CWDM4’s 2 km range entirely (CWDM4 MSA Rev 1.0, Table 2-2). ESR4 does not enter the picture: it is a multimode-lane design for OM4 runs measured in hundreds of meters.

Two practical nuances matter when ordering for exactly 40 km. First, lower-power “ER4 lite” variants reach about 30 km without FEC and 40 km only when the host enables FEC, so confirm the host’s FEC capability before ordering (vendor ER4-lite datasheets). Second, the TIA FOTC tabulation of the IEEE specification notes that links longer than 30 km within the same power budget are considered engineered links and must not exceed the specified insertion loss, measure the span before committing to 40 km.

If the measured budget is tight, or the route may later be extended, the 80 km-class ZR4 variant covers it. Both ends of the link must be the same class: an ER4-to-LR4 pairing fails on wavelength alignment, just as a CWDM4-to-LR4 pairing does.

An IEEE 802.3bm link budget is an allocation: transmitter launch power minus receiver sensitivity, minus penalties, distributed across the channel insertion loss between the two modules. Channel insertion loss covers everything in the middle, fiber attenuation (0.4 dB/km for OS2 fiber at 1310 nm in the IEEE tables), connector pairs, mechanical splices, and patch panels. IEEE 802.3bm allocates LR4 a maximum channel insertion loss of 6.3 dB, the TIA FOTC tabulation of the standard notes the range assumes a 2.0 dB connection-and-splice allocation, while ER4 receives 18.0 dB over the same fiber type (IEEE 802.3bm, tabulated in the TIA FOTC 100GBASE-LR4 and 100GBASE-ER4 application overviews).

Per-lane optics anchor both ends of that allocation. LR4-class transmitters specify −4.3 to +4.5 dBm average launch power per lane, with vendor datasheets listing per-lane receiver sensitivity around −10.6 dBm OMA (vendor QSFP28 LR4 datasheets). ER4-class transmitters reach up to +4.5 dBm per lane, while receiver sensitivity figures vary by vendor and FEC assumption, roughly −15 to −21 dBm OMA pre-FEC across ER4 datasheets. The CWDM4 MSA shows the same accounting: an 8.0 dB illustrative budget splits into 5.0 dB of channel insertion loss plus a 3.0 dB penalty allocation (Table 2-5), verified against a stressed receiver sensitivity of −7.3 dBm OMA at 5 × 10⁻⁵ BER (Table 2-4).

A planned 30 km metro span works out as follows. Fiber attenuation is about 12 dB (30 km × 0.4 dB/km); add a 2.0 dB connection-and-splice allocation and the channel loss is roughly 14 dB.

That fits inside the 18.0 dB ER4 budget with about 4 dB of margin for repairs and cable aging, but it exceeds the 6.3 dB LR4 budget, the same fiber that is “LR4-class” at 10 km needs ER4 optics at 30 km. If a measured span (OTDR or source-and-meter) exceeds 18 dB, move to ZR4-class optics or a DWDM line system rather than expecting the receiver to absorb the shortfall; the 100G DWDM transceivers guide covers that path.

Link-budget parameter (IEEE 802.3bm tables) 100GBASE-LR4 100GBASE-ER4
Operating range on OS2/G.652 fiber 2 m to 10 km 2 m to 40 km
Maximum channel insertion loss 6.3 dB 18.0 dB
Cabled fiber attenuation basis 0.4 dB/km (OS2, 1310 nm) 0.4 dB/km (OS2, 1310 nm)
Lane wavelengths (LAN-WDM) 1295.56 / 1300.05 / 1304.58 / 1309.14 nm 1295.56 / 1300.05 / 1304.58 / 1309.14 nm
Transmitter, average launch power per lane −4.3 to +4.5 dBm Up to +4.5 dBm
Receiver sensitivity per lane (OMA) ~−10.6 dBm (vendor datasheets) Vendor-dependent, roughly −15 to −21 dBm OMA pre-FEC
Planning notes 2.0 dB connection-and-splice allocation assumed Spans beyond 30 km within the same budget count as engineered links

ESR4, ZR4, and matching the module to the plant

ESR4 exists for buildings and campuses already wired with OM4. IEEE 802.3bm’s 100GBASE-SR4 reaches 70 m over OM3 and 100 m over OM4 with an MPO connector and four 850 nm lanes; vendor ESR4 documentation extends the same parallel-lane design to roughly 170 m over OM3 and 300 m over OM4 (Extreme Networks 100GBASE-ESR4 documentation; IEEE 802.3bm SR4 reach per the standard). Beyond 300 m on multimode fiber no IEEE PMD offers support, that is single-mode territory. The generic QSFP28-ESR4-100G listing in the YT CIG equipment catalog follows this extended-SR4 class.

ZR4 answers the opposite problem: spans beyond ER4’s engineered 40 km. Typical vendor datasheets specify 80 km over G.652 single-mode fiber on four LAN-WDM lanes, with deliberately hot transmitters (up to roughly +6.5 dBm per lane) and sensitive pre-FEC receivers (around −28 dBm OMA at a 5 × 10⁻⁵ BER target). Because no IEEE PMD defines this class, link budgets are vendor-engineered: check the module datasheet’s stated insertion-loss range against the measured plant, enable host FEC, and use the SFF-8636 digital diagnostics to watch per-lane received power drift with temperature. The generic QSFP28-ZR4-100G listing in the YT CIG equipment catalog follows this 80 km class.

ESR4 stays inside the building or campus duct (multimode, MPO, hundreds of meters); ZR4 is the duplex single-mode, LC duplex part for tens of kilometers. Between 2 km and 10 km, LR4 is the baseline; 10 km to 40 km is ER4 territory; beyond 40 km, or wherever measured loss exceeds 18.0 dB, the choice is ZR4 or a DWDM transport design.

Matching a module to a plant is a four-step exercise. First, classify the fiber: if both ends land on OM3/OM4 multimode with MPO panels, the choice is SR4 (to 100 m over OM4) or ESR4 (to 300 m over OM4); everything else assumes duplex single-mode fiber with LC duplex connectors. Second, size the span: length × 0.4 dB/km for OS2 fiber, plus every connector pair and splice, the IEEE 802.3bm LR4 tabulation allocates 2.0 dB for connections and splices, a workable first-pass figure for a link survey. Third, select the least expensive variant class whose budget covers the measured loss with margin: CWDM4 up to 2 km, LR4 up to 6.3 dB of loss, ER4 up to 18.0 dB, and ZR4 beyond that. Fourth, hold the wavelength plan constant end to end, no mixing CWDM4 with LR4, or LR4 with ER4, because the lane grids do not align.

Two habits prevent most field surprises. Measure the span whenever it sits within about 20% of a budget boundary: connector quality varies far more between panels than the 0.4 dB/km fiber figure does between reels. And confirm FEC capability early: the CWDM4 MSA requires host-side RS(528,514) FEC by specification (§1.7), ER4-lite variants need it for the full 40 km, and ZR4 datasheets state their sensitivity at a 5 × 10⁻⁵ pre-FEC BER, a host platform that cannot enable FEC may not deliver the datasheet reach.

What should you check before ordering a 100G QSFP28 module?

Compatibility, condition, and diagnostics are the three checks that separate a clean deployment from an RMA cycle. Compatibility: QSFP28 optics are platform-coded, so confirm the module against the switch or transport vendor’s compatibility matrix before purchase, the same optical class carries different order codes per platform vendor, as the ARISTA QSFP-100G-CWDM4, ERICSSON TOM-100G-LR4, and DELL EMC Q28-100G-LR4-G3 listings in the YT CIG equipment catalog illustrate. Condition: both new and refurbished 100G modules circulate in the secondary market; for refurbished units, ask the supplier for per-lane transmit and receive power readings at temperature plus a link test at rated reach, and confirm warranty terms. Diagnostics: any module bound for production should expose digital diagnostics per SFF-8636, so per-lane optical power, temperature, and alarm flags are readable from the host.

Then confirm the details that cause most mismatches: duplex LC (single-mode WDM variants) versus MPO-12 (multimode SR4/ESR4); the wavelength class on the label, CWDM4, LR4, ER4, and ZR4 share the LC duplex connector but sit on different grids; the operating temperature range for outdoor cabinets; and host slot power, vendor datasheets list about 3.5 W for CWDM4-class and 4.0 W for LR4-class modules.

Frequently asked questions

Can QSFP28 CWDM4 and LR4 modules interoperate with each other?

No. The CWDM4 MSA fixes four lanes on the 20 nm CWDM grid at 1271, 1291, 1311 and 1331 nm (Table 2-1), and IEEE 802.3bm fixes LR4 on LAN-WDM at 1295.56, 1300.05, 1304.58 and 1309.14 nm. No lane wavelength is shared, so a CWDM4 module and an LR4 module cannot be paired on one link; same class at both ends is a hard requirement, and a mixed spare pool has to be sorted before dispatch.

Is 100GBASE-ZR4 an IEEE standard?

No. The longest duplex single-mode PMD in IEEE 802.3bm is 100GBASE-ER4, at 40 km with an 18.0 dB maximum channel insertion loss. ZR4, commonly specified at 80 km, is a vendor-defined class on the same LAN-WDM lanes, so its budget comes from the module datasheet.

Does host FEC extend a CWDM4 link past 2 km?

No. The CWDM4 MSA already requires host-side RS(528,514) FEC and defines the optical link at a 5 × 10⁻⁵ pre-FEC BER (§1.7), so the correction is part of the specification and buys no extra reach. What caps the link is the operating range of 2 m to 2 km and the illustrative 8.0 dB budget (Tables 2-2 and 2-5), against roughly 16 dB of fiber attenuation on a 40 km OS2 span before any connectors. For 40 km, the answers are 100GBASE-ER4 (IEEE 802.3bm) or an 80 km-class ZR4 module.

What fiber does a 100G QSFP28 ESR4 module need?

Multimode fiber. ESR4-class modules extend the 4 × 850 nm SR4 design to roughly 300 m over OM4 and 170 m over OM3 on an MPO-12 connector, against the IEEE 802.3bm SR4 baseline of 70 m over OM3 and 100 m over OM4. Any single-mode run (including short ones where the plant is G.652) should use the WDM variants instead.

Why do CWDM4 and ZR4 datasheets quote a 5 × 10⁻⁵ BER instead of 10⁻¹²?

Because those links are specified before correction. The CWDM4 MSA requires host-side RS(528,514) FEC per clause 91 of IEEE 802.3bj and sets the optical link at a 5 × 10⁻⁵ BER with the correction still to come (§1.7); the host then delivers the 10⁻¹² class the Ethernet MAC expects. ZR4 datasheets inherit the same convention, which is why their sensitivity numbers carry a FEC assumption.

What management interface should a production QSFP28 module support?

SFF-8636, the management interface the CWDM4 MSA requires QSFP28 modules to comply with (§1.5). It exposes digital diagnostics such as per-lane transmit and receive power, module temperature, and alarm flags, which you will want when verifying a 40 km ER4 or 80 km ZR4 span against its measured loss budget.

Need a specific part?

Send the part number and quantity — we confirm condition, availability and price before you commit.