• Telecom & ICT Equipment Supplier
  • Multi-Vendor Sourcing
  • Worldwide Shipping
YT CIG Telecom & ICT Equipment
Get a Quote

Buying refurbished telecom equipment: inspection checklist

Updated on 2026-11-19

A refurbished unit arrives with a history you cannot see. The acceptance checklist below replaces that history with evidence gathered on delivery day: a physical inspection, configuration checks against the order, performance tests at the published specification, and a documentation review. Four groups, fourteen checks, one signed record.

Why does a delivery inspection checklist matter for refurbished telecom equipment?

Refurbished telecom equipment costs less than sealed factory stock, but it has already been installed, decommissioned and rebuilt by a party whose test depth you cannot see from a listing photo. A structured acceptance checklist turns that invisible refurbishment process into evidence you can hold: photographs, serial lists, DDM captures and a signed record, all dated.

Three reasons drive the discipline. Warranty windows on refurbished stock typically run from dispatch or receipt, so acceptance executed within days protects both sides. Claims need evidence: if a board fails two weeks after installation, the dispute outcome depends on the serials, alarm logs, optical power readings and photographs you recorded at receipt. And teams need repeatability, a procedure written as a checklist can be executed by warehouse staff or field engineers the same way for every shipment, from one vendor or ten.

The checklist below is organised in four groups (physical, configuration, performance and documentation) for the equipment classes a multi-vendor supplier typically ships: optical transceivers, switches and routers, SDH and microwave transport platforms, and radio access units.

What does a complete delivery acceptance checklist look like?

The master checklist below covers fourteen checks in four groups, run in five steps, prepare, inspect physically, verify configuration, test performance, close documentation. Record the result of every check, including the passes.

# Group Check How to check Pass looks like
1 Physical Transit packaging Photograph pallets, cartons and any tilt or shock indicators before opening Packaging intact; any damage photographed before unpacking
2 Physical Chassis and boards Inspect covers, slots, gold fingers and connector pins for bends, corrosion and tool marks No bent pins, no corrosion, no unscheduled rework marks
3 Physical Connectors and optics seats Check LC/APC ferrules, SFP/QSFP cages and backplane connectors for debris or cracked latches Clean ferrules, positive latch action, no debris in cages
4 Physical Cooling and power hardware With power off, spin fan trays by hand; check PSU handles, filler panels and air filters Fans rotate freely; power hardware complete
5 Configuration Part number match Compare chassis and board labels with the order line, including option code suffixes Part number and option code identical to the quotation
6 Configuration Serial numbers Record chassis, board, PSU and transceiver serials; match against the packing list Every serial matches the packing list and is logged
7 Configuration Hardware revision and software state Check revision labels against the quotation; cold-boot and confirm cleared configuration Revision matches; unit boots to default/cleared config
8 Performance Power-on self-test Watch a cold-boot POST; dump the event and alarm log POST completes without critical alarms; log reviewed
9 Performance Transceiver DDM audit Read digital diagnostics via CLI or NMS and compare with the datasheet window Temperature, voltage, bias and TX/RX power in range
10 Performance Optical link test Patch to a known-good span; record per-lane TX/RX power Values inside the datasheet window at the required reach
11 Performance Traffic, timing or radio tests Run RFC 2544-class Ethernet benchmarks; G.703/G.813 checks on SDH; radio evidence per 3GPP TS 38.104 Results meet the published specification for the unit class
12 Documentation Test report Match report serials to unit serials; confirm measured values are present Serial-matched report with real measured numbers
13 Documentation Warranty and RMA terms Read the warranty statement; note period, start date and claims route Period and start date stated in writing
14 Documentation Commercial and compliance papers Verify packing list, invoice and compliance marks for the destination market Papers complete and consistent with the shipment

Run the groups in this order:

  1. Prepare. Book a bench in an ESD-protected area (program requirements are specified in IEC 61340-5-1) and lay out the order, quotation and packing list.
  2. Inspect physically. Run checks 1–4 before applying power; photograph anything doubtful.
  3. Verify configuration. Run checks 5–7 against the quotation itself.
  4. Test performance. Run checks 8–11 with the minimum test set for the equipment class.
  5. Close out. Run checks 12–14, then sign the acceptance record or move the unit to quarantine with its evidence bundle.

Which pre-purchase checks reduce the risk of a failed acceptance?

Most acceptance failures begin weeks earlier, when the unit was specified or described loosely. Four pre-purchase checks cut that risk before money moves.

  • Pin the condition grade in writing. Suppliers use the same words (new, refurbished, used) for different levels of testing. Ask what the grade includes (functional test, firmware reload, cosmetic standard) and require the definition on the quotation. YT CIG’s equipment listings, for example, state that condition is confirmed on quotation (new, refurbished or used as applicable) and that every unit is inspected before dispatch.
  • Ask for a sample test report. A usable report shows the serial number, test items and measured values; a bare PASS supports no claim. A supplier that cannot produce one sample will not support its listing claims in a real dispute.
  • Match part numbers against the compatibility matrix. Option codes and suffixes decide whether a board or transceiver works in your chassis and software version, and a description can cover a dozen variants. YT CIG states it matches the part number and option code against the manufacturer’s compatibility matrix before quoting, a practice worth requiring from any supplier.
  • Fix the warranty anchor. Agree when the warranty clock starts (dispatch, arrival or acceptance) and who runs the RMA. Both points belong in the written offer; a chat message carries no weight in a claim.

These checks also shorten the delivery inspection: the quotation becomes the acceptance baseline. The multi-vendor equipment catalogue shows how suppliers typically present brand, part number and condition together per unit.

Physical and visual inspection

Physical inspection happens before power-on, catching handling damage and questionable rework before they become operating problems. Keep one photo record per unit: photographs are the most useful exhibit in a damage dispute.

Check 1, transit packaging. Photograph the pallets, cartons and any tilt or shock indicators before opening anything. If the packaging is damaged, photograph that first, then unpack slowly: an insurance or carrier claim depends on photos that separate transit damage from later handling.

Check 2, chassis and boards. Look for bent or discoloured connector pins, corrosion on gold fingers, tool marks on screws (a sign of field repair), and mismatched cover screws. Cosmetic grading is part of the purchase contract, agree what “refurbished” means for cosmetics before delivery, then verify against that definition.

Check 3, connectors and optics seats. Inspect LC/APC ferrules for chips or scratches, SFP and QSFP cages for bent guides, and backplane connectors for debris. A contaminated ferrule degrades return loss and can fail an otherwise healthy link.

Check 4, cooling and power hardware. With power off, spin each fan tray by hand: grinding or notchy rotation predicts a fan bearing failure. Confirm that PSU handles, filler panels and air filters are present.

Handle boards inside an ESD-protected area. The requirements for designing, establishing and maintaining such a program are specified in IEC 61340-5-1; in practice that means a grounded wrist strap, static-shielding bags and a grounded bench surface for every board that comes out of its bag.

How do you verify configuration and part numbers against your order?

Configuration checks tie the physical unit in front of you to the commercial agreement you signed.

Telecom hardware is sold in variants: option codes, hardware revisions, region codes and licence entitlements. A chassis with the right description can still be the wrong part.

Check 5, part number match. Compare the part number on the chassis or board label with your order line, character for character, including option code suffixes. Do the same for transceivers: a 100GBASE-LR4 QSFP28 module, listed in YT CIG’s catalogue as QSFP-100GBASE-LR4 (Juniper), is quoted and shipped by exact part number; the phrase “100G LR4” covers several parts.

Check 6, serial numbers. Record every serial: chassis, supervisor, line cards, power supplies and transceivers. Match them against the packing list. The serial list is what the warranty attaches to; if a serial is missing, scrubbed or inconsistent with the packing list, stop and resolve it before signing anything. The same list cross-checks the supplier’s test report later.

Check 7, hardware revision and software state. Verify that the hardware revision printed on the board matches what was quoted; revisions can change feature behaviour or power draw. Boot the unit and confirm it starts with a cleared, default configuration, a unit carrying the previous operator’s configuration is both an operational and a security liability. If your application depends on specific licences, check entitlement before racking, because licence transferability varies by vendor and program.

Keep one spreadsheet row per unit with serial, part number and hardware revision, attached to the acceptance sign-off. That table becomes the spine of the acceptance file.

Which performance tests should you run before accepting refurbished equipment?

Performance testing is where refurbished stock earns or loses trust.

The test set scales with the equipment class, but the principle holds: test against the published specification the unit had to meet when new, and record the measured values.

Optical transceivers. SFP/SFP+ and QSFP modules expose digital diagnostics through the management interface defined in SFF-8472: module temperature, supply voltage, transmitter bias current and TX/RX optical power, readable over the I²C bus from a CLI or NMS. Read those registers and compare them with the datasheet window. For the 100GBASE-LR4 class, Cisco’s QSFP-100G-LR4-S datasheet specifies a per-lane transmit power of −4.3 to +4.5 dBm and a pre-FEC receiver sensitivity of −10.6 dBm at BER 5×10⁻⁵; a refurbished module must sit inside the same window, because IEEE 802.3bm fixes 100GBASE-LR4 reach at 10 km over single-mode fibre (ER4 at 40 km, SR4 at 100 m over OM4). Then patch the module to a known-good span and confirm per-lane TX/RX power on the live link. Current catalogue examples are grouped on the 100G QSFP28 transceiver category page.

Wavelength accuracy (CWDM/DWDM). Confirm CWDM channels against the ITU-T G.694.2 grid (eighteen nominal wavelengths from 1271 to 1611 nm at 20 nm spacing) and DWDM channels against ITU-T G.694.1, whose frequency grid is anchored at 193.1 THz with 100 GHz and 50 GHz spacing options in the C-band (roughly 1530–1565 nm). A mislabelled or retuned DWDM optic passes a power test and still breaks the mux. Wavelength, not just power, is the acceptance value.

Ethernet switches and routers. Run an RFC 2544-class benchmark: throughput, latency, frame loss and back-to-back buffering across the standard 64–1518 byte frame sizes. RFC 2544 is a laboratory methodology (RFC 6815 narrows its applicability for production networks), so treat the results as comparative figures against the datasheet. The same benchmark applies to the data-centre spine switch class and carrier Ethernet access switches.

SDH and microwave transport. Verify E1 tributaries per ITU-T G.703, the 2048 kbit/s interface over 75 Ω coaxial or 120 Ω balanced pair with HDB3 line coding, and check timing output against ITU-T G.813, which specifies the wander and jitter masks for SDH equipment slave clocks. These checks apply to the STM-16 class SDH/MSTP multiplexers.

Radio units. For RRU/AAU-class equipment, require radio evidence traceable to 3GPP TS 38.104, which defines the minimum RF characteristics for 5G NR base stations; formal conformance testing is specified in TS 38.141-1/-2. This applies to the 4T4R remote radio unit class.

Equipment class Core test Method / reference What to record
QSFP28/SFP transceivers DDM audit + live link power SFF-8472 telemetry vs vendor datasheet Per-lane TX/RX power, temperature, bias
100G LR4/ER4/SR4 optics Reach-class conformance IEEE 802.3bm (LR4 10 km, ER4 40 km, SR4 100 m OM4) Link up, error counters, measured power
CWDM/DWDM optics Channel alignment ITU-T G.694.2 / ITU-T G.694.1 Nominal channel vs measured wavelength
Ethernet switch/router Throughput, latency, frame loss RFC 2544 benchmark, 64–1518 byte frames Per-port results at each frame size
SDH/microwave Tributary + timing ITU-T G.703 (E1) + ITU-T G.813 (SEC masks) Error counts, clock status
RRU/AAU radio units RF characteristics evidence 3GPP TS 38.104; conformance per TS 38.141-1/-2 Serial-matched report with band and power

What documents should arrive with a refurbished telecom shipment?

Documentation decides whether a passing unit becomes an accepted, warrantied asset. Five documents belong in the acceptance file.

  • Packing list with serial numbers, the master reconciliation document. Every serial recorded in the configuration group must appear here.
  • Commercial invoice, part numbers, quantities and values; needed for customs clearance and your asset register.
  • Test report, the acceptance evidence. A usable report carries the unit serial, the test items and measured values (per-lane optical power, alarm log status, throughput results); a bare PASS gives the acceptance file nothing to stand on. YT CIG states on its equipment listings that every unit is checked before dispatch and that documentation is supplied with the shipment; when ordering, ask specifically that measured values be included.
  • Warranty statement, period, start anchor and claims route. The equipment FAQ on YT CIG’s listings states that warranty terms depend on the manufacturer and product line and that the applicable period is stated on the quotation, which is why the quotation itself belongs in the acceptance file.
  • Compliance documentation, the conformity marks your destination market requires (for example, CE marking for equipment placed on the EU market). Radio products without the required marks cannot be licensed.

File all five with the signed acceptance record: serial list, test report, warranty statement and photographs form the complete evidence chain for a claim. Payment, warranty and delivery terms are summarised on YT CIG’s support pages.

Handling defects found at acceptance

A failed check starts a clock.

Quarantine, then record. Move the unit out of the installation flow, keep packaging and accessories together, and tag it with the check number that failed. Photograph the failure point, capture the alarm log or DDM output verbatim, and note the exact serial: “does not boot” is weak evidence, “serial X fails POST with error Y, reproduced twice on bench Z” is not.

Notify within the agreed window, and arbitrate from the test report. Supplier and carrier claims are time-limited, transit damage in particular, which is why the physical group runs on delivery day. Send the evidence bundle (photos, logs, serial, packing list reference) with a covering note limited to dates and facts. If the unit’s serial-matched report shows a value at the edge of the datasheet window at dispatch, your failure record and that report together define the fault timeline.

Resolve through the warranty route. YT CIG’s equipment FAQ states that the applicable warranty period is stated on the quotation and that claims are handled on the buyer’s behalf. With any supplier, agree the remedy (repair, replacement or credit) in writing before the unit ships back.

Frequently asked questions

Is a refurbished unit held to a lower specification than a new one?

No. Acceptance is run against the specification the unit had to meet when it left the factory, and the datasheet windows apply unchanged. What varies between suppliers is the depth of testing behind the word “refurbished” and the condition grade, and both should be stated on the quotation. Reliability comes from test depth and documentation, not from the label.

What does “tested” cover in a refurbished grade?

Depth varies more than the label suggests. The common grades are new (sealed factory stock), refurbished (tested and cosmetically graded) and used (as removed from service), but the testing behind “refurbished” splits into three levels: power-on and POST only; functional test with measured values recorded; and full optical or traffic test against the datasheet windows. Ask which level applies to the line you are buying, and have the answer written on the quotation or carried by the test report. A unit tested at the first level and one tested at the third can carry the same word on the invoice.

The test report arrives but covers a different serial. What then?

A report is evidence only for the serial it names. Quarantine the unit, ask for the report matching the shipped serial, and treat the mismatch as a documentation failure under check 12 until it is resolved. If the correct report cannot be produced, the acceptance record has no performance evidence for that unit, and the claim position weakens accordingly.

How do I check that an optical transceiver is genuine and compatible?

Two checks cover most cases. First, verify the part number and option code against the manufacturer’s compatibility matrix for your exact chassis and software version; YT CIG states it performs this match before quoting. Second, read the module’s digital diagnostics: SFF-8472 defines the management interface that exposes temperature, supply voltage and TX/RX power over the I²C bus. A deeper authenticity workflow is covered in the 100G QSFP28 transceiver guide.

How long should a delivery acceptance inspection take?

There is no fixed industry duration; scope the test set to the equipment class, then let the clock follow. RFC 2544, for example, defines the frame sizes (64–1518 bytes) and procedures for Ethernet benchmarks, so results stay comparable between units and suppliers however long a session runs. In practice the physical group runs on delivery day and the performance group inside the warranty-anchor window.

The warranty clock starts at dispatch, but the unit sat in transit for three weeks. Who carries that?

Warranty anchors are a commercial term, so fix the anchor before ordering. If the period runs from dispatch, transit and warehousing consume cover; ask for an acceptance-date anchor or an extension written into the offer. On YT CIG listings the applicable period is the one stated on the quotation, and terms depend on the manufacturer and product line, which is why the quotation belongs in the acceptance file.

Need a specific part?

Send the part number and quantity — we confirm condition, availability and price before you commit.